Commercial & industrial electrical services, New ZealandOffice Mon–Fri 7.30am–5.00pm · 24/7 call-outs · info@phasesafe.co.nz

Maintenance and troubleshooting

Emergency call-outs and electrical fault finding, 24/7

When power, plant or lighting fails, we find the fault, make the site safe and get you running again, day or night.

Phase Safe provides reactive fault finding and 24/7 call-outs for commercial and industrial sites across New Zealand, from bases in Wellington and Auckland. When a circuit keeps tripping, power drops out, plant stops or lighting fails, our licensed electricians trace the cause, make the installation safe and repair it. If a full repair needs parts or a planned shutdown, we make it safe first and tell you plainly what has to happen next.

What should you do when an electrical fault hits your site?

Turn off the affected equipment if it is safe to, keep people clear, and call us. Don't keep resetting a breaker that trips again straight away, don't open switchboards, and don't touch anything that may be live or damaged. If there is a fire or someone has been hurt, call 111 first. Everything after that is a job for a licensed electrician.

Treat it as urgent if you see or notice any of these:

  • Smoke, sparks or scorch marks at a switchboard, outlet or fitting
  • A burning smell, or a switchboard that is hot or buzzing
  • Exposed live parts or damaged cables
  • Water near electrical equipment
  • A circuit or RCD that trips immediately every time it is reset

Repair work on a building's fixed wiring is generally prescribed electrical work, which the Electricity Act 1992 restricts to people authorised to do it, such as licensed electrical workers.

Which electrical faults do we find and fix?

We work on the faults that stop commercial and industrial sites: circuits and RCDs that trip, partial or total loss of power, plant that won't start or keeps stopping, lighting failed across an area, and overheating switchboards and connections. Here is what usually causes each one.

Symptom Common causes What we check
Circuit or RCD keeps tripping Earth leakage, damaged cable or appliance, overload Insulation resistance, connected loads, the device itself
Part of the site has no power Failed breaker or fuse, loose connection, lost phase Supply at the main switchboard and distribution boards
Three-phase plant won't start or runs rough One phase missing, failed contactor or overload, motor fault Voltage on each phase, motor starter, motor windings
Lighting out across an area Tripped circuit, failed control gear or lighting controls Lighting circuits, drivers and controls
Board hot, buzzing or smelling Loose or overloaded connections, failing components Terminations, loads, components

How does an electrician find an electrical fault?

Good fault finding is a method, not guesswork. We start with what happened and when, make the affected part of the installation safe, and then test to narrow the fault down to a circuit, a cable, a component or a connected piece of equipment. The aim is to fix the cause, not just the symptom.

A typical call-out follows these steps:

  1. Gather information. What failed, when, and what changed on site.
  2. Make safe. Isolate the affected circuit or equipment and prove it is dead before working on it.
  3. Test and locate. Insulation resistance, continuity, voltage and load tests.
  4. Find the cause. A tripping breaker is usually doing its job; what is it reacting to?
  5. Repair and retest. Fix the fault, test the circuit and restore supply.
  6. Report. What we found, fixed and still recommend.

What are the most common types of electrical faults?

Most faults fall into four groups. A short circuit is a low-resistance path between conductors that causes a large current. An earth fault is current escaping to earth through metalwork, damaged insulation or a person. An open circuit is a break, such as a loose terminal or a broken cable, that stops supply. An overload is a circuit carrying more current than it was designed for.

Three-phase sites add one more: loss of a phase, which can leave motors running hot or unable to start.

What does making the site safe involve?

Sometimes a full repair can't be finished on the first visit: parts need ordering, a shutdown needs planning, or the fault is in equipment another contractor maintains. Making safe means isolating the faulty part, restoring supply to the rest of the site where it is safe to do so, and labelling what has been left off and why. We then quote or schedule the permanent repair.

The Electricity (Safety) Regulations 2010 require anyone doing electrical work to protect people and property from its dangers while they work, and anything unsafe that we isolate stays off until it is repaired.

How do 24/7 call-outs work?

Call-outs for electrical faults are available 24/7, including nights and weekends. Our office hours for quotes and planned work are Mon–Fri 7.30am–5.00pm. When you call, tell us the site address, what has failed, how we get access and any induction rules, so the electrician arrives with the right gear.

How can you stop the same fault happening again?

Repeat faults usually have a cause that a quick reset hides: a board running near capacity, a connection slowly overheating, or plant that has outgrown its circuit. After a call-out we tell you the likely cause and whether it may recur. Regular checks and thermal scans through planned and predictive maintenance catch most of these before they stop the site.

Frequently asked questions

Can you get an emergency electrician at night or on a weekend?

Yes. Phase Safe offers 24/7 call-outs for electrical faults on commercial and industrial sites, including nights and weekends. Our office hours for quotes and planned work are Monday to Friday, 7.30am to 5.00pm, but a fault that stops your site doesn't have to wait for them.

Do circuit breakers detect earth faults?

A standard circuit breaker protects against overcurrent, meaning overloads and short circuits. It only trips on an earth fault if that fault draws enough current. A residual current device (RCD) is the device that detects current leaking to earth, at levels far too small to trip a breaker, and cuts the supply to protect people from electric shock.

Why does a breaker keep tripping?

A breaker or RCD that keeps tripping is reacting to something: an overload, a damaged cable, moisture, a faulty appliance or a failing component in the board. Resetting it again and again doesn't fix the cause and can make damage worse. Unplug or switch off what is on the circuit if it is safe to do so, and call us.

Can we keep using equipment after a fault?

Not if it may be unsafe. The Electricity (Safety) Regulations 2010 say an owner or operator must not use, or let anyone else use, an installation or appliance that is electrically unsafe. If equipment has tripped repeatedly, overheated or been damaged, keep it off until an electrician has checked it.

Sources