Commercial & industrial electrical services, New ZealandOffice Mon–Fri 7.30am–5.00pm · 24/7 call-outs · info@phasesafe.co.nz

Switchboard guide

Do you need a switchboard upgrade? Signs and NZ rules

How to tell when a switchboard is due for an upgrade, and what the New Zealand rules say about it.

Updated 10 November 2026

You probably need a switchboard upgrade if the board trips without an obvious cause, runs warm or smells of burning, still uses rewireable fuses, has no RCD protection, has no spare ways for new equipment, or sits on an asbestos-containing backing. Business changes such as a new tenancy, a fitout or new machinery are common triggers too. For what the work involves, see our commercial switchboard upgrades page.

Signs a commercial switchboard needs upgrading

The clearest signs are physical: tripping, heat, burning smells, discolouration and old fuses. Others are about capacity and protection, such as a board with no RCDs or no room for new circuits. One sign on its own does not always mean replacement, but each is a reason to have a licensed electrician look at the board soon rather than at the next fitout.

  • Frequent tripping or blown fuses. Repeated tripping on the same circuits usually means overloading, a wiring fault or tired protective devices.
  • Heat, buzzing or a burning smell. A warm cover, crackling or a smell of hot plastic points to loose connections or overloaded parts. Treat it as urgent.
  • Discolouration or scorch marks. Brown or black marks around breakers, terminals or the backing board show that something has been running hot for some time.
  • Rewireable fuses. Old ceramic holders with fuse wire are easy to over-rate with the wrong wire and give no protection against electric shock on their own.
  • No RCD protection. Residual current devices cut the power within a fraction of a second when current leaks to earth. Older boards often have none, or only one RCD covering many circuits.
  • No spare ways. With no space for another device, new equipment ends up on overloaded circuits.
  • Asbestos backing. Many older boards were mounted on backing boards containing asbestos. You cannot confirm it by looking; it has to be tested.
  • Damage or water. Cracked covers, corrosion, water stains or exposure to weather or vehicles all need attention.

Business changes that trigger a switchboard upgrade

Even a healthy board can stop fitting the business. The most common commercial triggers are a change of tenancy, a fitout or refurbishment, new machinery, kitchen equipment or EV chargers, and findings from an insurer, a thermal scan or an electrical audit. Each one either adds load, changes how the space is used, or puts the board's condition on record, which makes it a sensible time to plan an upgrade.

  • Tenancy change. A new tenant often needs different circuits, separate metering or a distribution board of their own.
  • Fitout or refurbishment. New layouts mean new circuits, which need spare ways and protection that meets the current wiring rules.
  • New machinery or equipment. A compressor, a CNC machine or a commercial oven may need three-phase supply, larger protective devices or a sub-board close by.
  • EV chargers. Each charger needs its own circuit and protection and draws a steady load for hours. Our commercial EV charging page covers how supply and board capacity are checked.
  • Insurer or audit findings. An insurer's survey, a thermal imaging report or a maintenance audit may flag hot spots, missing RCD protection or an unsafe board.

What New Zealand rules say about old switchboards

New Zealand law does not require every old switchboard to be replaced. The Electricity (Safety) Regulations 2010 let an existing installation stay in use and be maintained or repaired, as long as it is not unsafe. When you alter or add to it, though, the parts you change must meet the edition of the wiring rules, AS/NZS 3000, that the regulations cite at the time.

From 13 November 2025 the regulations cite AS/NZS 3000:2018, including Amendments 1 to 3, in place of the 2007 edition. WorkSafe's guidance says existing installations can continue and be repaired with no time limit, and parts you do not touch need no upgrade. Work where construction begins after 12 November 2026 must comply with the 2018 edition.

Regulation 59 also allows maintenance or replacement that restores an installation to its original condition or follows the fitting manufacturer's instructions. So a like-for-like repair of a sound board can be lawful, while adding circuits brings in the current rules for that work.

All of this is prescribed electrical work. Under the Electricity Act 1992, only people authorised under the Act, in practice licensed electrical workers, may do it, and it must be tested and certified.

RCD protection when you alter or add circuits

When circuits are added or altered, the new or changed work has to meet the cited wiring rules, which set out which final subcircuits need additional protection from 30 mA RCDs. On an old board with no RCDs, adding a circuit usually means adding RCD protection for it, and that is often the point where the board runs out of room.

The New Zealand amendments also changed what kind of RCD is acceptable. Any RCD in an installation must suit the types of load it serves, taking account of pulsating and constant direct-current fault currents, which some electronic equipment can produce, and RCDs in some clauses must be Type A, Type F or Type B. RCD testing must now include trip time and confirmation that the device actually protects against shock.

The exact clauses depend on the installation and the circuit, so ask your electrician to show in the quote which circuits will get RCD protection and why.

Asbestos-backed switchboards: what the rules require

WorkSafe notes that many older fuse boxes were mounted on asbestos-containing backing boards, and that some also contain friable parts such as asbestos flash guards. The Health and Safety at Work (Asbestos) Regulations 2016 put duties on the business that manages or controls the workplace, and set out who may remove which kind of asbestos. Your electrician and, where needed, a licensed removalist do the work; you are responsible for identifying it.

  • Identify or assume it. A business that manages or controls a workplace must identify asbestos where there is a risk of exposure, or assume it is present (regulation 10). If it is identified or likely, a written asbestos management plan is required (regulation 13).
  • Before refurbishment. For structures and plant built before 1 January 2000, asbestos likely to be disturbed by refurbishment must be identified and, so far as reasonably practicable, removed before the work starts (regulations 19 and 25). Minor or routine maintenance is excluded.
  • Who may remove it. Friable asbestos needs a Class A licensed removalist (regulation 54). Non-friable asbestos needs a licensed removalist once the project total is more than 10 m²; at or below that, a competent person trained under the regulations may remove it (regulation 27).

WorkSafe's safe work sheet for these fuse boxes adds that if any friable parts remain, or the board is fixed to asbestos insulating board, a Class A removalist must remove it, and the new board must go on a non-asbestos surface. If unsure, have an asbestos surveyor check it first.

What to do if your switchboard shows warning signs

If you notice any of the signs above, do not open the board, do not keep resetting a breaker that trips repeatedly, and do not fix anything to or drill near an older board. Note what happened and when, take a photo from a safe distance with the cover closed, and call a licensed electrician to inspect it.

If there is smoke, fire or a strong burning smell, get people clear and follow your building's fire procedure. Otherwise, an inspection shows whether repair, upgrade or replacement is the right call, and our guide to what a switchboard upgrade costs explains how each is priced.

Frequently asked questions

Do I need to upgrade my switchboard?

You need to act if the board trips repeatedly, runs hot, smells of burning, is damaged, or cannot take the circuits your business now needs. An old board that is sound and not overloaded may only need repairs. A licensed electrician's inspection, sometimes with a thermal scan, tells you whether repair, upgrade or replacement is the sensible option, and what the rules require for the work you plan.

Is it illegal to have an old switchboard in New Zealand?

No. WorkSafe's guidance on the amended Electricity (Safety) Regulations says existing installations can continue to exist and be repaired, with no time limit, as long as they are not unsafe. What changes is any work you do: parts that are altered or added must meet the current cited edition of AS/NZS 3000. An unsafe board must be fixed regardless of its age.

Does adding one circuit mean replacing the whole switchboard?

Not always. If the board has a spare way, a sound enclosure and room for the RCD protection the new circuit needs, one circuit can usually be added to it. If it is full, has rewireable fuses, has no space for RCDs or sits on an asbestos-containing backing, adding a circuit often makes a replacement or an extra distribution board the practical choice.

How do I know if my switchboard has asbestos?

You cannot tell reliably by looking. Older boards and fuse boxes, especially in buildings from before 2000, are the usual suspects, but only testing of a sample confirms it. Check whether the building has an asbestos survey or management plan first. If not, a business that manages the workplace must either have it identified or assume asbestos is present, and plan the work on that basis.

Can my staff reset or work on the switchboard?

Staff can generally switch off or reset a breaker that has tripped once, if they can do it without removing covers. Anything beyond that is prescribed electrical work, which only licensed electrical workers may do. A breaker that trips again straight away, a hot board or a burning smell all mean leaving it alone and calling an electrician.

Sources