Updated 16 November 2026
Test and tag in New Zealand is usually charged per item, plus a call-out fee or minimum charge for each visit. Published 2025–26 price lists mostly put standard work at about $2–$6 per item excluding GST, with lower rates for large volumes and a minimum for small jobs. This guide breaks down those figures and what moves them. For how a visit runs and what gets tested, see our test and tag service for workplaces.
How much is test and tag in NZ?
For a typical workplace, expect roughly $2–$6 per item excluding GST from published New Zealand price lists, plus a call-out fee or a minimum booking. A site with 100 items would therefore land somewhere around $250–$650 excluding GST once a call-out is added. Small jobs cost more per item, because the minimum charge is spread over fewer tags.
These are indicative figures taken from published New Zealand price lists, not Phase Safe prices. They change with the provider, the region and the site, and any real number depends on a quote.
| What you're paying for | Typical published range (NZ, 2025–26, excl. GST) |
|---|---|
| Standard test and tag, per item | About $2–$6 |
| Large volumes on one site (hundreds of items) | Towards the low end, sometimes under $3 |
| Call-out or travel fee per visit | About $50–$65, or none with a minimum booking |
| Minimum charge for small jobs | Varies widely, from a small package price to several hundred dollars |
| Microwave leakage and other specialist tests | Usually an extra charge per item |
Two patterns stand out. Dedicated test and tag businesses tend to price lower per item. Electrical contractors tend to price higher, but the same visit can also cover the repair of what fails.
How much is a PAT test per item?
A PAT test (portable appliance test) is the same thing as test and tag, and published New Zealand rates run from about $1.50 to $6 per item excluding GST for standard work. The lower end applies to large volumes on one site. The higher end covers small jobs and electrical contractors. Specialist tests, such as microwave leakage, are usually priced separately.
Microwave leakage testing is normally an extra charge per item on top of the standard rate. RCD testing may also be a separate line on the quote, depending on how many portable and fixed RCDs the site has.
Is there a call-out fee or minimum charge?
Most providers charge one or the other. Published New Zealand call-outs sit at roughly $50–$65 excluding GST, and minimum bookings range from a small package for a handful of items to several hundred dollars. Some nationwide providers advertise no call-out fee and recover their travel time in the per-item rate.
The minimum matters most for small offices. If you only have 15 items, a minimum booking can cost more than the per-item rate suggests. Ask how the minimum works before you book, and whether a second site on the same day attracts a second call-out.
What changes the price of test and tag?
Five things move a test and tag price more than anything else: how many items you have, how spread out they are, how often the environment needs testing, how many items fail, and any extra tests or out-of-hours work. Two sites with the same number of items can be priced quite differently.
- Number of items. The biggest factor. Per-item rates fall as volume rises, and the call-out is spread over more tags.
- How spread out the site is. Twenty items in one office is quick. Twenty items across four floors, a yard and a locked storeroom take longer. Several sites mean travel between them.
- Testing interval. Higher-risk environments are tested more often, so you pay more times a year. Construction sites are the clearest example: WorkSafe's guide for small construction sites says portable outlet assemblies should be tested by an electrician at least every three months, and the AS/NZS 3760 interval table (2010 edition) suggests six months for factories and workshops. Our test and tag requirements guide covers the intervals.
- Failed items. A failed item is normally charged at the same per-item rate as a pass. Repairing or replacing it is extra. A new lead or power board is often cheaper than repairing an old one.
- RCD and specialist tests. Operating-time tests on RCDs and microwave leakage tests are often priced separately.
- After-hours work. If equipment can only be tested when the site is closed, expect a different rate. Phase Safe works Mon–Fri 7.30am–5.00pm; talk to us about after-hours work if you need it.
- Reporting. Most providers include a report. Some add a reporting or administration fee per site.
How can you keep test and tag costs down?
The cheapest test and tag is a well-prepared one. Have equipment accessible and switched off where it can be, retire items nobody uses, and set intervals by actual risk rather than testing everything at the shortest interval. Grouping sites into one visit and replacing tired leads before the visit also cuts cost and repeat failures.
A few practical steps:
- Clear out dead equipment first. Broken heaters and spare leads in a cupboard still get tested if they are on site. Dispose of what you no longer need.
- Make items reachable. Equipment behind locked doors or under stacked stock slows the visit down.
- Set intervals by environment. AS/NZS 3760 does not ask for the same interval everywhere. A computer in a quiet office can go much longer between tests than a drill in a workshop, and over-testing low-risk gear adds cost with little safety gain.
- Keep your register. A good register means a repeat visit is faster, because items are already identified and located.
- Book multiple sites together. One plan across several sites usually costs less than separate visits arranged at different times.
- Do the daily checks. Staff who spot a damaged cord and pull it out of use early reduce failures on the day.
Is it cheaper to buy a test and tag machine?
For most businesses, no. A New Zealand test equipment supplier lists portable appliance testers from about $1,500 to $3,800 excluding GST for the tester alone, and complete kits cost more. You also need a trained person, register software, tags, and time away from their normal job. In-house testing tends to make sense only for organisations with large fleets.
WorkSafe accepts either route: a business can buy the testing equipment and train a worker, or hire a third party. Whoever does it must understand AS/NZS 3760 and be able to apply it. If you go in-house, you still need a registered electrical worker to repair what fails.
How does Phase Safe quote for test and tag?
Phase Safe has no fixed price list for test and tag, because the cost depends on your site. We ask for a rough count of items, where they are, how many sites you have, and whether construction or workshop equipment is involved. From that we put together a quote before any work is booked. Testing is carried out by certified testers, and any repairs by our licensed electricians.
If you already have a register from a previous provider, send it with your enquiry. It gives us an accurate item count and shows which areas are due first. For multi-site businesses we can quote a testing plan that covers every location on the right cycle, with reminders when each one is next due.
Frequently asked questions
How much is test and tag in NZ?
Published New Zealand price lists from 2025–26 mostly charge about $2–$6 per item excluding GST for standard work, plus a call-out fee or minimum booking. Larger volumes bring the per-item rate down, while small jobs pay a minimum charge. Electrical contractors tend to sit higher per item. Treat any figure as indicative until you have a quote for your own site.
How much is a PAT test per item?
A PAT test is the same as test and tag. Published New Zealand rates run from about $1.50 to $6 per item excluding GST, with the lowest rates for sites with hundreds of items. One published electrical contractor rate works out at about $10 per item excluding GST. Microwave leakage and RCD tests are often priced separately from the standard per-item rate.
How much does a test and tag machine cost?
A portable appliance tester is a significant purchase. One New Zealand test equipment supplier lists testers from about $1,500 to $3,800 excluding GST, with complete kits costing more. On top of that you need training, tags, software and staff time. For most small and medium businesses, hiring a provider costs less than buying and running the equipment.
Does the test and tag price include repairs?
No. The per-item rate covers inspection, testing, tagging and reporting, whether the item passes or fails. Repairing or replacing a failed item is a separate cost, and repairs must be done by a registered electrical worker. Phase Safe is an electrical contractor, so we can quote repairs or replacements for failed items in the same report.
